View CAT5126ZI-50-GT3_1224141.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CAT5126
One-Time Digitally Programmable 32 Tap Potentiometer
FEATURES
Wiper position stored after one-time nonvolatile programming User-defined Power-On wiper position 32 tap positions Wiper position programmed through simple 2-wire serial interface Low 0.35A (typ) static supply current 2.5V to 5.5V single-supply operation 10k, 50k, and 100k end-to-end resistances 50ppm/C end-to-end temperature coefficient and 5ppm/C ratiometric temperature coefficient 8-Pin TDFN (2mm x 3mm) and MSOP packages
DESCRIPTION
The CAT5126 is a digital programmable potentiometer. The wiper position is controlled with a simple 2-wire digital interface. This digital potentiometer is unique in that it has an optional onetime programmable feature that either sets the wiper's position upon power-on to a user-defined value, or the wiper can be set and the interface also disabled to prevent further adjustment. The CAT5126 has an end-to-end resistance of 10k, 50k, and 100k. All CAT5126 devices have 32 wiper positions and operate from a single 2.5V to 5.5V supply. The CAT5126 is available in 8-pin TDFN and MSOP packages. Each device is guaranteed over the industrial temperature range of -40C to +85C. For Ordering Information details, see page 10.
APPLICATIONS
Mechanical potentiometer replacement Products using one-time factory calibration Contrast, brightness, volume controls Programmable analog functions
PIN CONFIGURATION
MSOP (Z) (top view)
RW CS VDD GND 1 8 RH RL U/D VPP
FUNCTIONAL DIAGRAM
RH 8 VDD 3 GND 4 2 UP/DOWN COUNTER 6 32-POSITION DECODER ONE-TIME PROGRAM BLOCK RW 1 RW R30 R31
2 CAT 7 3 5126 6 4 5
CS U/D
TDFN (VP2) (top view)
RW CS VDD GND 1 2 3 4 8 7 6 5 RH RL U/D VPP
VPP 5
R2
R1
7 RL
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
1
Doc. No. 2129 Rev. A
CAT5126
PIN DESCRIPTION Pin 1 2 3 4 5 6 7 8 Name RW CS VDD GND VPP U/D RL RH Function Wiper Connection Chip-Select Input. A high-to-low CS transition determines the mode: increment if U/D is high, or decrement if U/D is low. CS is also used for one-time programming (see the One-Time Programming section). Power-Supply Voltage Ground Programming Voltage for One-Time Programming. Connect VPP to 10V supply when one-time programming the device. For normal operation, connect to ground or let float. Up/Down Control Input. With CS low, a low-to-high transition increments or decrements the wiper position. Low Terminal of Resistor High Terminal of Resistor
ABSOLUTE MAXIMUM RATINGS(1) Parameters VDD to GND VPP to GND All other pins to GND Maximum Continuous Current into H, L, and W Continuous Power Dissipation (TA = +70C) 8-Pin MSOP (derate 4.5mW/C above +70C) 8-Pin TDFN (derate 24.4mW/C above +70C) Operating Temperature Range Junction Temperature Storage Temperature Range Lead Temperature (soldering, 10s) Ratings -0.5 to +7.0 -0.5 to +12.0 -0.5 to VDD +0.5 1.5 362 1951 -40 to +85 +150 -65 to +150 +300 Units V V V mA mW mW C C C C
Note: (1) Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
Doc. No. 2129 Rev. A
2
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
CAT5126
ELECTRICAL CHARACTERISTICS VDD = 2.5V to 5.5V, VPP = GND, RH = VDD, RL = GND, TA = -40C to +85C, unless otherwise noted. Typical values (1) are at VDD = 5.0V, TA = +25C, unless otherwise noted. Symbol RES RPOT TCRPOT TCRATIO INL DNL RW Parameter Resolution -10 Device End-to-End Resistance TC of Pot Resistance Ratiometric Resistance TC Integral Nonlinearity Differential Nonlinearity Wiper Resistance Potentiometer configuration, no load Potentiometer configuration, no load VDD = 5V VDD = 2.5V 0.7 x VDD 0.3 x VDD 0.1 5 2.5 (Note 2) VDD = 5V VDD = 2.5V VPP = 10V 0.35 0.25 8.5 6.0 5.5 1 1 10 10 5 1 -50 Device -00 Device 8 40 80 Conditions Min Typ 3.2 10 50 100 50 5 0.5 0.25 70 150 12 60 120 300 20 1 0.5 100 200 ppm/C ppm/C LSB LSB V V A pF V A mA V A k Max Units %
DC PERFORMANCE
DIGITAL INPUTS (CS, U/D) VIH VIL IIN CIN VDD IDD IDDW VPP IPP Input High Voltage Input Low Voltage Input Leakage Current Input Capacitance Supply Voltage Stand by Current Programming Current Programming Voltage VPP Input Current
POWER SUPPLY
Notes: (1) All devices are production tested at TA = +25C and are guaranteed by design for TA = -40C to +85C. (2) Digital inputs CS and U/D are connected to GND or VDD.
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
3
Doc. No. 2129 Rev. A
CAT5126
ELECTRICAL CHARACTERISTICS (continued) VDD = 2.5V to 5.5V, VPP = GND, VH = VDD, VL = GND, TA = -40C to +85C, unless otherwise noted. Typical values are at VDD = 5.0V, TA = +25C, unless otherwise noted.(1) TIMING CHARACTERISTICS (2) Symbol tCU tCI tIC tIL tIH tIW tPC tCP tCL tCH tPH fU/DMAX tUP tSETTLE Parameter U/D Mode to CS Setup CS Hold to U/D Mode U/D Step Hold to CS U/D Step Low Time U/D Step High Time Wiper Switching Time VPP Rising Edge to CS Falling Edge CS Falling Edge to VPP Falling Edge CS Step Low Time CS Step High Time VPP Falling Edge to CS Rising Edge U/D Frequency Power-Up Time Output Settling Time (Note 3) 100k variable resistor configuration, CL = 10pF 100k potentiometer configuration, CL = 10pF 1 s 0.25 Conditions Figures 1, 2 Figures 1, 2 Figures 1, 2 Figures 1, 2 Figures 1, 2 CL = 0pF, Figures 1, 2 Figure 3 Figure 3 Figure 3 Figure 3 Figure 3 1 5 5 5 1 5 1 Min 50 50 0 100 100 100 Typ Max Units ns ns ns ns ns ns ms ms ms ms ms MHz ms
Notes: (1) All devices are production tested at TA = +25C and are guaranteed by design for TA = -40C to +85C. (2) (3) Digital timing is guaranteed by design, not production tested. Power-up time is the period of time from when the power supply is applied until the serial interface is ready for writing.
Doc. No. 2129 Rev. A
4
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
CAT5126
TYPICAL OPERATING CHARACTERISTICS VDD = 2.5V to 5.5V, VPP = GND, VH = VDD, VL = GND, TA = +25C. VPP vs. VDD
10 9 8 7 6 5 2.5 3.5 4.5 5.5 300
IDD programming vs. VDD
Valid Programming
ICC (uA)
250
VPP (V)
200
Invalid Programming
150
100 2.5 3.5 4.5 5.5
VDD (V)
VDD (V)
Wiper Resistance vs. Tap Position @ 25C
120 100 80
Wiper Voltage vs. Tap Position
6.0
VDD = 2.5V
5.0 4.0
R W ( )
VDD = 5.0V
60 40 20 0 0 10 20 30
V W (V)
3.0 2.0 1.0 0.0 0 10 20 30
VDD = 5V
VDD = 2.5V
Tap Position
Tap
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
5
Doc. No. 2129 Rev. A
CAT5126 DETAILED DESCRIPTION
The CAT5126 devices are 10k/50k/100k (end-toend resistance) digitally controlled potentiometers. They have 32 tap positions that are accessible to the wiper along the resistor array between RH and RL. The wiper (RW) position is adjusted sequentially through the tap positions using a simple 2-wire interface. These digital potentiometers have an optional one-time programmable feature that sets the POR position of the wiper. The 2-wire interface can then be disabled, permanently preventing unwanted adjustment. low-to-high transition at the U/D increments or decrements the wiper position depending on the current mode. The value of the counter is then stored and the wiper position is maintained till the device is Powered down. The wiper performs a make-before-break transition, ensuring that there is never an open circuit during a transition from one resistor tap to another. When the wiper is at either end (max/min) of the resistor array, additional transitions in the direction of the endpoint do not change the counter value (the counter does not wrap around). One-Time Programming The factory-set default position of the wiper on powerup is tap 16. However, the power-up position can be changed once using the one-time programming feature. After the wiper is moved to the desired position, the programming sequence is initiated by setting U/D high, CS applying 10V to VPP, and then taking low. Five pulses on (consisting of starting from low and CS CS going high for tCH and then low for tCL) program the device (Figure 3). The programming voltage should then be taken to zero. After the device is programmed, VPP can be set to zero or be allowed to float. The wiper position is still adjustable, but always returns to this programmed position on power-up.
DIGITAL INTERFACE OPERATION
The CAT5126 devices have two modes of operation when the serial interface is active: increment mode and decrement mode. The serial interface is only active when CS is low. The CS and U/D inputs control the position of the wiper along the resistor array. When CS transitions from high to low, the part goes into increment mode if U/D is high (Figure 1), and into decrement mode if U/D is low (Figure 2). Once the mode is set, the device remains in that mode until CS goes high. A
Figure 1: Increment Mode Serial Interface Timing Diagram
VDD CS
tUP tCU tCI tIL tIH tIC
U/D tIW VW
Figure 2: Decrement Mode Serial Interface Timing Diagram
VDD CS
tUP
U/D
tCU
tCI
tIH
tIL
tIC
tIW VW
Doc. No. 2129 Rev. A
6
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
CAT5126
If the intent is to program the device to a specific wiper position and not to allow further adjustments, then six programming pulses are required (as opposed to five), as shown in Figure 3. The sixth pulse locks the wiper position and disables the serial interface. This also allows U/D and CS to float without any increase in supply current. Once the lockout bit is set, no further adjustment to the potentiometer is possible, effectively changing the potentiometer into a fixed resistor-divider (Table 1). It is recommended that the user either use six CS pulses (convert to a fixed voltage-divider) or five Table 1. One-Time Programming Mode Mode Factory Default Programming with 5 pulses at the midscale position Programming with 5 pulses different from midscale position - only once Programming with 5 pulses if the power up position was changed before Programming with 6 pulses if the tap position is at midscale Programming ONLY with 6 pulses if the tap position is different from midscale position Power Up Position At midscale At midscale At the new programmed position At the previous programmed position Midscale position forever At the new programmed position Interface Active Active Active Active 2-wire interface active till power down 2-wire interface active till power down Operation Programming allowed Programming allowed No further change in powerup position allowed None 2-wire interface disable after next power-up 2-wire interface disable after next power-up pulses (program the initial power-up value of the device, but still be able to adjust the wiper). If the device is programmed with five pulses and later it is desired to disable the interface (convert to a fixed voltage-divider), then care must be taken to ensure that the wiper is in the same position as it was originally set to (when programmed with five pulses). The full six programming pulses must be applied. Note that once the six-pulse program occurs, no further programming is possible.
Figure 3: One Time Program Mode Serial Interface Timing Diagram
U/D
10V
VPP
0V
tCH tPC
tCL
CS
tCP
tPH
5 BITS PROGRAM WIPER POSITION
OPTIONAL LOCKOUT BIT
Notes: (1) (2) If CAT5126 is Programmed with less than 5 pulses, it does not change the Power-up recall position. During internal power-up the wiper is forced to miscale; thereafter the wiper is set at the stored position.
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
7
Doc. No. 2129 Rev. A
CAT5126 PACKAGE OUTLINES
8-LEAD MSOP
E1
E
e
e
e
D L2 GAUGE PLANE b A1 L L1
A2
A
c
SYMBOL A A1 A2 b c D E E1 e L L1 L2
MIN 0.05 0.75 0.28 0.13 2.90 4.80 2.90 0.40
NOM 0.10 0.85 0.33 3.00 4.90 3.00 0.65 BSC 0.60 0.95 REF 0.25 BSC
MAX 1.1 0.15 0.95 0.38 0.23 3.10 5.00 3.10 0.80
0
6
For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf.
Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC Specification MO-187. (3) Stand off height/coplanarity are considered as special characteristics.
Doc. No. 2129 Rev. A
8
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
CAT5126
8-LEAD TDFN (2mm x 3mm)
A
E
PIN 1 INDEX AREA
D
A1
A2 A3
D2
SYMBOL A A1 A2 A3 b D D2 E E2 e L
MIN 0.70 0.00 0.45 0.20 1.90 1.30 2.90 1.20 0.20
NOM 0.75 0.02 0.55 0.20 REF 0.25 2.00 1.40 3.00 1.30 0.50 TYP 0.30
MAX 0.80 0.05 0.65 0.30 2.10 1.50 3.10 1.40 0.40
b e 3xe E2
PIN 1 ID
L
For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf.
Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-229.
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
9
Doc. No. 2129 Rev. A
CAT5126 EXAMPLE OF ORDERING INFORMATION
Prefix CAT Device # 5126 Suffix Z I -10 - G T3
Company ID Product Number 5126
Temperature Range I = Industrial (-40C to 85C) Resistance -10: 10k -50: 50k -00: 100k
Tape & Reel T: Tape & Reel 3: 3000/Reel Lead Finish G:NiPdAu
Package Z: MSOP VP2: TDFN
ORDERING INFORMATION
Ordering Part Number CAT5126VP2I-10-GT3 CAT5126VP2I-50-GT3 CAT5126VP2I-00-GT3 CAT5126ZI-10-GT3 CAT5126ZI-50-GT3 CAT5126ZI-00-GT3
(4) (4) (4) (4)
Resistor [k] 10 50 100 10 50 100
Top Marking GF EJ EH ABRA ABMY ABMV
Package-Pin TDFN TDFN TDFN MSOP MSOP MSOP
Part Per Reel 3000 3000 3000 3000 3000 3000
Notes: (1) All packages are RoHS-compliant (Lead-free, Halogen-free). (2) The standard lead finish is NiPdAu. (3) The device used in the above example is a CAT5126ZI-10-GT3 (MSOP, Industrial Temperature range, 10k, NiPdAu, Tape & Reel). (4) For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office.
Doc. No. 2129 Rev. A
10
(c) 2007 Catalyst Semiconductor, Inc. Characteristics subject to change without notice
REVISION HISTORY
Date 03/14/07 Rev. A Reason Initial Issue
Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: Beyond MemoryTM, DPPTM, EZDimTM, LDDTM, MiniPotTM, and Quad-ModeTM Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc. Corporate Headquarters 2975 Stender Way Santa Clara, CA 95054 Phone: 408.542.1000 Fax: 408.542.1200 www.catsemi.com
Document No: 2129 Revision: A Issue date: 03/14/07

▲Up To Search▲

Price & Availability of CAT5126ZI-50-GT3

	To Download CAT5126ZI-50-GT3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .